How do I calculate rotation caused by bounce friction?

Question

Following on from my previous question: I have the ball quite realistically bouncing from surfaces it hits. Now I'd like to make it spin from the friction of the hit.

Showing this is simple enough: I rotate the ball by its angular velocity every tick and apply the same rotation when it's rendered.

When a ball hits a wall, I know that the speed of rotation is affected by...

• the ball's initial speed when hitting the surface
• the friction coefficients of the ball and surface (physical constants)
• the angle of incidence (the angle between the ball's incoming velocity vector and the surface normal).

The angle of incidence is approximated by the dot product of the ball's impact and exit velocity vectors. (1 meaning high spin, -1 meaning no spin, and everything else relatively in between)

Multiplying all of the above together and making sure they were then transformed to the range 0 - 1, and multiplied by max rotation speed, the ball seemed to respond in rotation speed as expected. Except for one thing: It would always rotate clock-wise (because of positive values).

---

Is this a good method? Can you think of a simpler way?

If this method seems fine, what am I missing? How do I know when the ball should be rotating counter-clockwise?

Answer 1

Your method is nice, because it's very simple. One thing you might need is dependency on previous spin on the ball, which you do not take into account. The spinning ball represents rotational energy, so a realistic simulation would probably have to conserve it along with the other energies.

However, if the ball is not rotating upon impact, I can't imagine a situation in which it begins rotation against the direction of the incident angle. That is, "clockwise" or "counterclockwise" should be relative to whichever side of the normal the incident angle is.

I think simply multiplying the result by the original x-direction vector (+1 if traveling left to right, -1 if traveling right to left) should do it.

Edit: You can use the cross-product for this. Incident cross normal provides a vector in the Z direction only (if we are on the 2D x-y plane). Look at the z-element: if it is positive, the ball's approach should cause it to spin clockwise. If it is negative, the ball should spin counterclockwise.

Answer 2

First get the surface tangent from the surface normal: t = (ny, -nx)

Then you can get the velocity component along the surface as vt = v dot t.

Now you can calculate the rotation of the ball: w = |(normal * r) cross vt|, where r is the radius of the ball.

Here I assume the ball has no rotational inertia and begins to spin instantly at the speed it would if it was to roll along the surface. You can use a coefficient of friction to make it more realistic and, if you want, take into account the rotational inertia of the ball.

Answer 3

Ókay, this might sound stupid but you're not using the dot-product of the ball vector and the surface normal and just doing an arccos to calculate the angle are you? Because then the angle would be positive whether it was positive (up to 90 degrees) or negative (ditto) as cosine is symmetrical around 0.
If this is the case then instead of using the normal of the plane, use the plane direction itself and subtract 90 degrees from the angle, so 0 to 180 would become -90 to +90 degrees (or -half PI to +half PI if you're radially inclined).

Answer 4

The first thing you need to adress is wheter the rotation speed or spin before hitting the wall; lets say Si; is greater, equal or lower than the value needed to maintain the same spin after hitting, say Ss. With this you can get the actual after hitting spin, say Se, using a friction value between the ball and the surface

Get the velocity component across the bouncing surface Vxi= Vi dot Vx, being Vx a parallel vector to the surface with magnitude 1.

The value you are looking is Ss= Vxi/r , this is to transform Vxi into angular speed. If Si is lower than Ss the ball should gain spin positively. If Si is equal to Ss the ball should keep aproximately the same spin, about this later. If Si is greater than Ss the ball should lose spin

the loses and gain of speed depend on the frictional value Fr. Actually it is a Cross between the radius and hte frictional force, but you can set that value as you wish.

You must also notice that besides the bounce coef, the ball loses some energy due to a friction between the ball and surface, thus Vxi is affected negatively. I would say bounce coef affects Vy and friction affects Vx.

You should take into account the deformation of the ball. This will affect the time or frames the ball is stick to the wall, thus the fritional force will exert for a longer time affecting spin and exit velocity. This deformation depende on how you want your model to be.